Best Secure Travel Router 2018 For A Mac10/20/2021
We have redacted its identifiable information as our goal here isn’t to provide a free penetration test to the hardware manufacturer. Also a multifunctional titan among the best travel wireless routers, the RAVPower FileHub Plus Wireless Travel Router instantly converts wired networks into wireless networks that can bridge and extend WiFi, which allows internet to be securely shared with others in your network.In this blog post, we will demonstrate the techniques used to assess security on a generic portable router purchased online. RAVPower FileHub Plus Wireless Travel Router. Time Machine will automatically suggest that.1. Two layers of network address translation (NAT) can create problems but I think it depends on the protocol used, web and email will probably be fine.Network administrators should perform security assessments of hardware that they will provide their users, or particularly paranoid users might want to poke at their devices just to be extra sure.An AirPort Time Capsule, Apples wireless router with network-attached storage, which you set up on your network. For routing, the travel router shouldn’t be any different than using a personal home access point/router in front of an ISP-supplied one or a Mac using Internet sharing.Best USB WiFi Adapter for Travel 2018 A wireless adapter makes it possible for your computer or other device to connect to the Internet without needing wires no matter where you travel. If your router has only the older. A new standard announced in 2018. The best Wi-Fi routers to bring.These are typically called either “plated-through holes” or “annular rings.” We will just refer to them as plated-through holes for this exercise.This looks suspiciously like an interface that the manufacturer left on the mainboard. We’ll come back to them later.The board has four unpopulated pin holes. This page contains a ton of good info on the chipset, its capabilities, where it is sold, and by who.Let’s file those tidbits of information away for now. The main chip in the center was an MIPS processor, and there’s a specific model number silk screened onto the mainboard.Some light Googling revealed that this chipset has a manufacturer website and even a product-specific page.I also found a WikiDevi page on our exact model. WikiDevi is a user-editable database for computer hardware based on MediaWiki and Semantic MediaWiki. These are illegal.Taking the router apart revealed the main router board with two antennae and one chip in the center. Thankfully, there weren’t any of the warranty “void if tampered” stickers.We purchased a “third hand” to hold the mainboard. More equipmentIn order to get a better look, we did some online shopping. But the plated-through holes are in an awkward position, and examining the mainboard is difficult. This looks promising, like a good place to start. There’s no attempt made to hide its purpose.After some light digging on the product website, we did find mention of the slow I/O features of this chipset.Further, Googling showed that this pinout is fairly common and might be of the UART variety.There’s mention of UART on the product page.
Best Secure Travel Router 2018 For A Free Penetration TestThis meant we were going to try and be as delicate with our probing as we could. The LED lights also made examining the main board much easier.To interact with these pins, we could solder wires in, but we’re planning on using this device, provided it passes muster. Back to the Internet to get a jeweler’s lamp.So now we had the magnifying lamp, and it is much better than the little one that comes with the third hand. The chips on the mainboard are pretty small, and our eyesight isn’t what it used to be. This means we are in the proximity of 120 Volts, so we should exercise a modicum of caution.This device is compact and tightly integrated. On line classes for microsoft excel for macWe started with checking for voltage. We settled on the Extech EX330 Autoranging Mini Multi-Meter with Built-In Thermometer and Type K Remote Probe.We also purchased the additional probe connectors kit for good measure. Did they have voltage? Were they used to send and receive information? Back to the Internet again for more shopping.Not wanting to buy something too cheap or inappropriate for the task, we Googled affordable voltmeter and found a review for decent and affordable voltmeters. No solder needed, plus easy access for eventually connecting the USB header and for probing the pins.Now we needed to investigate what those diagnostic pins were. Quickly inverting the probes gave us +3.3 Volts.Some quick Googling told us that there are two common voltages used in these types of interfaces: 3.3 Volts and 5 Volts. Maybe it was special? So we started by applying the ground to it and power to the top pin, and the result was -3.3 Volts. Diving inThe bottom plated-through hole had a square about it. We set the voltmeter to 200 Volts, just to be safe, and got to probing. It typically steps down from 120 Volts to 12 Volts. We found a USB to RS232 TTL UART PL2303HX Converter USB to COM Cable Adapter Module.We also found some that specified that they came with both voltage selections and, just to be thorough, we also ordered one of these. More shoppingSo back to more shopping. Let’s also store this tidbit of information for later. We found pictures of other UART interfaces on other routers.It does not appear that there’s a standardized pin order, but in most of the examples we found online, gnd (ground) and VCC are at the outer edges.In our case, VCC would stand for “Voltage Common Collector.” More Googling indicated that there is a cable available to interface with these pins and, most importantly, that you don’t need to connect the 3.3 Volt pin unless you want to watch your cable, your router, and potentially your computer go “poof-the-magic-dragon.”Good to know. This left the two center pins as a mystery.Many other much more talented people than us have gone down this particular rabbit hole, and in this, Google was invaluable. We plugged in the UART to USB cable in our test machine and encountered another roadblock.While it was properly detected and Windows did install the correct drivers, it didn’t work. We made an assumption and theorized that the cable coloring would be the same as the Google picture results (fingers crossed).Colors matched: black for ground, red for power, green for receive, white for transmit. Similar USB to UART cables had documentation on the web. This is achieved by issuing this command:So now we know that the USB adapter is ttyUSB0. What a surprise! Not to be easily defeated, we rebooted into Ubuntu Linux with the USB dongle still attached.We then proceeded to check if the USB to serial adapter was working. And more specifically, to this entry:“Windows 8/8.1/10 are NOT supported in PL-2303HXA and PL-2303X EOL (End Of Life) chip versions.”So while this USB dongle presumably works, it won’t work in Windows 10. Again, no go.Digging a little further into the properties of the device revealed that the device cannot start.Researching this error yielded this forum post. We also tried moving the USB device to a different port (from USB v3 to regular USB). We tried downloading the driver directly from the Prolific website and again weren’t met with success. It was installed with this command:We found that for best results, invoking GtkTerm from bash needed sudo. In Linux, we elected to use GtkTerm. In Windows, we would’ve used the Putty terminal program.
0 Comments
Leave a Reply.AuthorErica ArchivesCategories |